Load Definition and 1000 Threads

http://i59.tinypic.com/727ole.jpg My answers http://i59.tinypic.com/mkzvqp.jpg Can some see if I am going in the right direction, thanks.

hi i'm using Matlab/simulink to create a microgrid model which simulate dynamic control of power based on the loads. the loads are changing based on the realtime. I use several voltage sources to power the loads. I would like to be able to turn on/off the generator based on the loads. for...

Homework Statement Hi, I am having trouble with the following problem and I can't seem to find any examples: I am trying to determine reactions at points A and D of the redundant structure below using the unit load method, there is a 10kN load at the top left point (B), all lengths are...

I am looking for an explanation of why over correction of inductive loads can result in large circulating currents. Many sites give some form of vague verbal description but I have not been able to comprehend this phenomenon. Can anyone explain it mathematically or provide a link that...

Referring the question and my own worked out solution in the attachment, I could not get to the answer given that is Ra= 200 N, and Rc = 1300 N. Is there any calculation mistake I made?

Homework Statement Attached. Homework Equations The Attempt at a Solution Attached. For #2, how do I get VL and IL?

Hi, I have observed that as the load applied to a transformer secondary is increased (i.e. Increased Impedance), the current drawn by the transformer seems to decrease. Is this purely due to the fact that because the voltage remains fairly constant and the impedance is increased, the current...

Hi, I'm a sophomore undergrad and recently I've been wondering how much weight grad schools in the sciences actually put into your "course load." I've read some conflicting views on the internet, books on grad school admissions, and faculty. The websites for some grad/professional schools list...

Homework Statement For the overhanging beam in the figure, A) draw the moment diagram indicating all critical values including the maximum moment (Value and location), and B) write the moment function, M(x), for B-C section in terms of x coordinate as shown in the figure. Homework...

Could i get some help with this one please The ultimate strength of a round steel rod is 620.000 MPa. If a factor of safety of 3.000 is required, what is the maximum permissible load for the rod if it has a diameter of 3.000 cm?

Hey guys. I need a resistive dummy load that can handle 2.5 W, but I need it to be much smaller than a 2.5 W resistor. I have looked for different ideas, but I need it to be simple like a resistor and smaller than a 2.5 W resistor. Any ideas?

What is the best/easiest method I can use to get the deflections of a 5-storey, 3-bay frame subjected to lateral loads only? I've used the Elemental stiffness matrix for two-dimensional frame analysis (giving me a 60 x 60 matrix) but I'm getting the wrong deflection values. I think my procedure...

Hi guys this semester I am graduating this semester with a math degree and I am for sure taking these four classes: 1. Real Analysis 1 2. Numerical analysis 2 (differential equations/pde's, more advanced methods than numerical methods 1) 3. Electrodynamics (griffiths) 4. Spanish...

"Determine working stress and greatest allowable load" Homework Statement The maximum load in a tensile test on a mild steel specimen of diameter 12.5 mm is 95 kN, calculate the ultimate tensile stress. Also, determine the working stress and greatest allowable load on a rod of the same...

Finally finished up the snow load calculator. Moved it to this page: http://design.medeek.com/resources/snow/snow_calculator.pl Give it a whirl and let me know what you think. I wish there was an easy way to calculate the ground snow loads for a given location but unfortunately there...

Hey guys, so I'm building a mini wind tunnel and I would like to calculate the new RPM,HP and Torque since the propeller will act as a load and change the specs of the motor(note I'm using a air wrench as the motor as it's all I had around and have disabled the impact motion) the current specs...

Hey guys. Im building a special type of squat rack for my gym, and need some input on the bolts to use. I have used high tensile M16 bolts on all joints, but am not sure if it is enough, hence me joining this forum and asking you guys. Attached is a picture, and Ill explain the lines I've...

Supposed you have a beam supported by 2 columns at the beam ends. At the middle of the beam, let's say there is a point load, the weight shared by the 2 columns is 1/2 each. How about if the point load is in the 3/4 portion of the beam, what is the corresponding share of each column of the...

I have been given this question by my teacher as part of a quiz and I'm confused on how to start. 1. Calculate the maximum working tensile load that a 19mm shaft is able to take with a safety factor of 3. Material UTS 470 Mpa 2. Stress = load/area When it states 'area' what is this the are of...

A cast iron pipe is filled with concrete and used as a column to support a load W.If the outside diameter of the pipe is 200mm and the inside diameter is 150mm, what is the maximum permissible value for W if the compressive stress in the concrete is limited to 5 KN/m2. Take E for concrete as...

I'm trying to determine what equations I can use in order to calculate the maximum load (in pounds) across a sheet of plexiglass. Could anyone help me look in the right direction? This is just a sheet that's 10" x 10" x 1/8", that's held by 4 screws. You see, my project involves placing my...

Alright, I took a while setting this problem up for you guys, because I am absolutely stumped and have hit a brick wall and have nowhere else to turn for assistance. Please excuse the shoddy diagram. I made it from scratch to try to illustrate the problem better. Homework Statement Find the...

Homework Statement hello friends,i have to do a project about calculations of cooling of a car engine.i don't know what to do or where will i start.can you offer me some links or books about this area please.how can i find how many wats of heat, say, a 100 kw engine, releases. Homework...

Homework Statement Hey guys. I have a transmission line with a known characteristic impedance (50 Ω) of length L that is connected to an antenna that has a complex impedance of (50-j25)Ω. I am having extreme difficulty determining the minimum length (expressed in wavelengths) of line such...

Homework Statement http://postimg.org/image/7vpxry28t/ Can someone explain how they calculated the force R representing the distributed load? Did they even make use of the value "800N/m" from the question?

Homework Statement The problem along with its solution is attached as TheProblemAndSolution.jpg. Here is the textual part of the attached image: “In Fig. 1 a 20 ft-frame PQ is supported at two points L and M, 6 ft and 4 ft respectively from the edges. If a 300 lb load is attached to edge...

Homework Statement Can you simplify rectangular expression 1/j30 + 1/10 + 1/(15-j25) The answer is .134 angle(28.07) Homework Equations The Attempt at a Solution I got = 1/j30 + 1/10 + 1/(15-j25) = -j.03+.1+.06+j.04 = .16 + j.01 = .16 angle(3.57) The...

hello i do have something unclear about =.. POWER Real Power Reactive Power Inductive Load 500 511 W 329VAR 1.2 400 519W 312VAR 2.0L 300 490W 382VAR 3.2L IS ABOUT MIXED RESISTIVE INDUCTIVE LOAD.. MY...

Homework Statement I'm given this configuration with a AC source at v_{i} with a R_{sig} connect to the source before the capacitor. R_{sig} = 0.6 KΩ R_{G} = 1 MΩ R_{D} = 2.7 KΩ R_{L} = 4.7 KΩ I_{DSS} = 10 mA v_{p} = -6 V Homework Equations The Attempt at a Solution...

If you have a purely resistive load, which is connected to the generator via elements such as (transformer, transmission line etc), will the load power factor still be unity or 1.0 (In theory)? Or do the previous components such as transmission line etc affect the load power factor? Many Thanks...

In modern buildings (I'm talking about taller structures, apartments, etc. not houses) that have a reinforced concrete framework are the internal / external walls (usually brick, masonry etc.) ever load bearing? In the sense is the strength / integrity of the structure ever depending or...

Hello, I graduated last year for mechanical engineering and have a project that i am working on at home that i need some help on with the electrical part. what i am trying to build is a shock dyno, i need to measure force and velocity, i plan on using a lvt and a load cell unless someone has a...

Homework Statement This is a final hurdle of a long question designing a simple gear train. That is done but now am not sure of my calculations for power in / out and torque in and out, so hopefully someone can help? OK - I have 4 spur gears inline, Gear A = 100 rpm 80 Teeth (input motor...

To be honest, this problem was gone over symbolically in my discussion session, but I didn't fully understand it. I am having difficulties using the superposition method (or even force method) to solve these problems where a load is applied on the bar and it is constrained at both ends. I don't...

Homework Statement Well actually we were doing a beam experiment in class. It consisted of varying the position of a load and measuring the reactions to eventually analyse the relationship between the distance of load from 1 support with the 2 reactions. The reactions were provided by two...

Introduction Dear all, I'm working on an assignment to model a ship-to-shore crane for a FEM design course. Having modeled the crane, I now need to apply the load of the trolley (which is hoisting the container) on the boom (which in my case is a lattice structure made up of beam elements)...

Homework Statement Please refer to the image attached. I don't understand why can they just take 1.8m as the original length, since there is already a load hanging there. My calculations yield the value of strain to be e/L, but in the answer it is e/1.8. Please explain this to me. Homework...

Homework Statement The bar 1 in the figure has a cross-sectional area of 0.75 in^2. If the stress in this bar must be limited to 30 ksi (30,000 psi) determine the maximum load that P that can be supported by the structure. Homework Equations σ = F/A τ = Fd The Attempt at a...

Can someone help me regarding a concept in gun mechanism?? In the current mechanism a part of the chemical energy of the gunpowder is used to load the next bullet.Had this energy not been used to load , would it increase the range of the gun?? and if so, then is the increase significant??

I am trying to load a very old version of Photoshop 6.0 into my Win 7 computer. It won't even install, it just stopped. Is there any compatibility mode I can make it work? Thanks Alan

Greetings; I am a firefighter so physics is pretty much Greek to me. I work primarily as a rope rescue/USAR tech. We work a lot with rope, pulley's, and anchor points. All of these systems have angles that affect the loading in our system. Now I been taught rules of thumb when constructing a...

Homework Statement Homework Equations Time Avg. Power = \frac{|V0+|^2}{2*Z0} [1-|\Gamma|^2] for line of l=\frac{λ}{4}+n\frac{λ}{2} (where n=0 here), Zin=\frac{Z0^2}{ZL} The Attempt at a Solution Bit confused what to do in the 1st part? I know that max. power is delivered to load when...

I just realize my new laptop has no CD or DVD drive. I need to load anti virus and other programs in. I know all I need is to go and buy a USB DVD drive. But is there any way for me to copy the content of the DVD or CD into a USB flash drive using another computer. Then plug the flash drive into...

I came across a diagram of a release mechanism, which shows the operator how to double a release load. I have taking a basic physics course (not advanced) and I can't seem to make any sense of this. I am just trying to understand this diagram; is it correct? Sorry for the drawing; hopeful that...

Homework Statement Determine the load impedance for the circuit depicted in fIG 11.40 if the source is operating at a PF of (a) 0.95 leading: (b) unity: (c) 0.45 lagging. Homework Equations uploaded The Attempt at a Solution uploaded. I am not really sure what to do please see...

It's been a while since I had my last circuits class, so I'm just looking for some verification on my calculations. I have a series of lights that I want to combine to 1 circuit (if possible). Each light fixture has 2 bulbs, and I have a total of 12 fixtures, meaning 24 bulbs. I am using...

I started by getting the equation for the reaction(which is really simple). I'm a bit confused here, they're asking for the absolute maximum moment, but they're not locating the location of where the maximum moment will occur, should I assume it's happening on the middle of the beam? And another...

I started by getting the equation for the reaction(which is really simple). I'm a bit confused here, they're asking for the absolute maximum moment, but they're not locating the location of where the maximum moment will occur, should I assume it's happening on the middle of the beam? And another...

Is there a physicist who has discovered this, and could you explain how he/she did it? I was trying to find it on the internet, but it only gives me a lab review of load vs efficiency. thank you

Homework Statement Need to know the bearing load for a linear slide I'm working on, two spaced bearings with an extended load off the end of the slide. Homework Equations What equation do I need to apply? What examples are out there? The Attempt at a Solution