Ansys workbench Definition and 55 Threads

I was looking for a respond on moving mesh using COMSOL, while I was searching on Google I found a response in your forum.

Hi, I have one question related to the boundary conditions I should apply in a Static Structural simulation for the following support. The support is subjected to the following loading conditions shown below...

Hi I have a project regarding micromechanics of composites. I'm starting my analysis on the Fiber Matrix RVE. Right now I'm trying to find the natural frequency of the unit cell. The Unit cell has some unique geometry which I will keep on changing to see how natural frequency changes. I have...

Hello Guys I am New here on the foum Well i am simulating a static structure (Picture attached) on ansys and til now i have a result divergence when i apply different forces. i guess my loads and fixed supports aren't well defined. Please Help i know it s a bit long but please give it some time...

Hello, I want to model in Ansys Workbench contact between bricks and mortar. From experiments I know maximum normal stress and maximum shear stress. Respectively I know forces in which the contact fails. The failure is brittle due to lost of adhesion. I tried to use "Bonded contact" and...

thanks for you sir i want to se how can i plot the contact pressure vs axe x (mm) in ansys workbench.? its very important for me

Hi all, I'm currently working on my bachelor's thesis in mechanical engineering. I must simulate a brake model, which consist of 1 rotor and 1 stator. The rotor rotate around z-axis and the stator move along z-axis. When pressure is on stator placed. The stator and rotor will be pressed...

I am using the static structural module of ANSYS workbench to do a simulation. In my model, there is a gear and a spring which presses against the gear, moves along it and pushes it to turn counterclockwise. These two objects are in frictional contact. In my calculation, I always have the...

Hey folks, I am doing a structural static analysis in ANSYS Workbench. A problem has troubled me for several days. Here it is: I would like to connect object 2 to object 1 by a revolute joint, which allows 2 to follow the movement of 1 and to rotate around this joint at the same time (under the...

I'm currently working on my bachelor's thesis in mechanical engineering. A part of my thesis is conducting a FEM-analysis on a sump for sewage. I've applied a load on the upper face of the lid for the sump. As a result, the upper layer of the lid has been "pushed through" the lower layer of...

Using : Ansys Workbench 16 Educational I want to build simple frame and simulate stress state and deformation when that frame is lifted. I have constructed my geometry in Design Modeler using line body's. My lifting cable has circular cross section with diameter of 10 mm. My frame has square...

Hi, I have problem of finding the deformation of skin using a probe. I have identified the different layers of skin and made the model accordingly along with a probe in contact with the top layer of skin. The model is basically 15x15mm model with extrudes of different thickness for each layer...

Hi all, I have been simulating the following rhombus compliant mechanism using Ansys Modal analysis to have a quick understanding about its mode shapes,,,, the problem is that the deformation is extremely large you can see this as the scale is (*10^-5 ) . This result is for sure unrealistic but...

Hello ansys users in ANSYS workbench, how can I plot the contact tool results (Frictional stress, sliding distance...etc) with length (500mm for example) in the "x-axis" instead of the default "by time" option?. the path method can not be used with this type of results "Contact tool results"...

hi.. i want to import only the geometry defined in mechanical apdl into ansys workbench so that i want to have the freedom to change the geometry and meshing whenever i want to. thankyou

Hello, can I have one simple question? I need create a Multibody Parts in Ansys Workbench. But I haven´t a Design Modeller. How do I create it? Thanks you. Pavel

Please help.I want to do transient analysis on welded joint.So for moving heat source I have to select multiple patches along the weld joint.From tutorial I came to know that it can be done by imprint faces while extruding lines,but when I tried it by extrusion in operation it does not show the...

Hello All, I am a master student working on my thesis. am using ANSYS workbench to model the debonding between FRP and Concrete (Single Shear Test). The geometry is very simple, so meshing and sketching were easy. however I have the following quires about loading and interfaces. 1. I want to...

Hello! I started recently to use ANSYS Workbench 15 to solve a stiffness problem of a three parts assembly. I have a general knowledge about FEM. I create the geometry in the Design Modeler by inserting the assembly from Solidworks 2010. It is a three parts assembly like a bicycle's wheel. Two...

Hello, I am trying to make contact between a stationary line body and a moving plate that will compress the line body. But I could not make contact between them. There is also a automatic connection generated but while simulation it does not show the contact instead the moving plate...

This is more complicated than it sounds. I'd like to analyse a fracture in a surface body so I need to create a no thickness or infinitesimally small cut/slice if it is possible. Afterwards, I'm planing to analyse stress concentration factor in model environment.

Hi all, I am trying to open my model from v.16 into v.15 with no success. I have dragged a mesh/Finite element modeler from my original model and Write solver model in an Ansys Mechanical APDL file and got to save my model as an inp. When reopening a FEM in ansys 15 and importing this (Inp...

Hi, I am trying to simulate a moving load in ansys 15. Could anybody guide me on how I could do it? A typical example: Calculating stress across a steel Rope ( assume solid circular c/s) between point A to B while a pulley load moves over it between the 2 points with a certain velocity. I will...

Hello.. i am trying to determine the maximum deflection of a beam on account of its sagging due to its own weight. I have the CAD MODEL of the beam and i import its IGS into ANSYS WB14.static structural. 1.is it a uniform distributed loading case? 2.i need to simply support the beam at both...

Hi, i solved a model but i got an error saying that "The solver engine was unable to converge on a solution for the non linear problem as constrained". Can someone offer advice on how i can fix this error?

Hi, I am carrying out a transient structural analysis of an expanding fastener in ANSYS Workbench 15. The model was created in Catia and imported into Workbench using DesignModeller. I believe I have defined my problem properly in Mechanical but it just hangs when I solve the solution. What i...

i am new to ANSYS, i designed a wind turbine blade in solidworks, when i try to create mesh it gives me an error. Previously i have made a mesh for a wind turbine blade i used >mapped face mesh then i used sizing and it was done but this blade is a bit different as it has 3 airfoils used in it

I'm new with ansys if I can help it would be helpful. the problem is that two solids are shocked, but one of them is going through the other, have already implemented several things different tutorials but the answer is the same. the only question when I change the location fixed support the...

I have done the following Steps on a geometry consisting of 2 Beams 5 Frames and an outer covering over that with Thugs on it for fix supports Steps 1. Import Geometry to Workbench 2. Geometry cleaning(Suppressing the unwanted parts and sheet ) 3. Open it in design Modeler 4. Meshing...

Hi everyone, I'm here to ask you one thing of ansys, I made this model with solidworks and I imported into ansys as STEP files (which is the difference in how import solidworks file?), I defined the part that will be studied and applied as you can see in the attached photo, a linear...

Hi everyone! I am doing a simulation of threaded connection in ANSYS workbench and have some problem. In this 2D model, the initial make-up is modeled by setting an "initial overlap" (shown in figure 1). This is how I did: - The initial contact between pin and box as "frictional" with...

Hi, I am new to Ansys workbench. I am doing analysis with simple fillet joint between two plate. I would like to learn about creation of weld joint/connection between plates. Anybody can help me to create such realistic connection. -Gajanan

How to create a script geometry. Is it possible? some type? I need to create a script to pipe conveyor. After entering the input data is created geometry. pls help me

Hello everyone, First of all, I want to excuse for my not perfect English since it isn't my mother tongue. However, now to my problem, which I'm facing at the moment. As part of my master thesis I have to simulate the application of a fastening device, which I develope during my master...

I have an assembly of two 2D surfaces. I modeled it on SolidWorks however, I could not import it to Ansys in any format. I tried SLDASM, Step and IGES. I tried modelling the same on Workbench modeller. However, I could not figure out a way to model 2D assemblies on the modeller. Can someone...

Hi all, I have started learning ansys workbench for steady state heat transfer based analysis. I am doing this analysis to validate analytical results given for heat transfer from a single plate fin. The fin tip is given a base temperature and heat transfer is calculated for natural...

I am trying to run a simulation (transient analysis) in ANSYS Workbench of a rolling tire on a flexible pavement surface. The tire is a truck tire with pressure of 0.7 MPa. I defined various outputs at consequential small time steps, and I can see the tire gradually inflating until (what...

Dear Friends, Hi,I am senior mechanical engineering student and I'm working on my final project which is designing an AGV vehicle.I designed a space chassis for it and have a problem with analyzing the joint I designed using Solidworks.I do not know how can I should define support...

Hello, I have the following problem: I would like, from a tungsten filament which an electric current is imposed, find the temperature emitted from the filament (Joule heating) on ansys workbench. I have to study a thermoelectrical , but I can not find any tutorial. Does anyone have...

I'm just learning how to use Ansys Workbench 13 to analyze static structures. I need to analyze the deformation of a simply supported beam with a concentrated force in the center vertically downward. I have a 3D model of this beam created in Solidworks. How do I create a force in the center...

Hi all, I learned to use Ansys workbench to do mechanical analysis, but never got any result. It always show me an error message: general error happened. The error details is below, "The license is currently in use by another application in this Workbench session such as...

Hi all, I did simple problem, in which assembly is subjected to single load & it is fixed at other end. I used Higher Order Tet element (& tried with Hexdominent Method also) for the casting body. The vonmises stress shows the true results but when i was looking for the Max Principal...

I have a box, the bottom and the four walls are made of grid. I wan to apply load in the box and see how the bottom and the four walls deform (and stress too). How can I do it? I do not want to apply a force to each wire vertically and horizontally. I want to apply a load to the bottom and the...

I am required to do scripting in ansys workbench...i know python, jscript and APDL can be used for this...now how do we really use them? jscript can be used with help of sendcommand() in python for geometric modelling...can we use APDL in python? In Mechanical(formerly simulation) can we...

I have modeled a curved surface to which I need to applied forces defined in a Excel csv sheet. I have successfully created an external data box in the project schematic and tried to import the load into mechanical. The load file I have resembles: X Y Load 0.3...

Hi, i am currently doing a simulation of rotating propeller using ANSYS Workbench v13. May i know how to obtain vibration data? coz i only able to obtain stress, strain & etc for solution.. I am currently using static structural analysis only. Do i have to use random vibration analysis?

hi there is an assembly of parts which i want to do static analyse on. i make the parts in cataia and import them as ''igs'' into workbench.problem 1: there are near 7 parts in my assembly which when gets into ansys , ansys doesn't recognize some of them and doesn't show them but it recognize...

Hello, I am a new user both in Ansys and in the forum and I am sorry if my question is silly, but I cannot find the solution by myself. I am using Ansys Workbench v.12 static structural in order to find the displacement of various parts of a robotic arm, that are caused by different loads...

Hello, I am used to use Ansys classic in my work. I just started to learn Ansys Workbench. I am modeling a copper jacketed lead bullet. I modeled the copper case the internal lead part. Now I have two solids. Is there a way to mate them, and use them as one assembly, of solids? Thanks