Materials and Chemical Engineering Forum

Is this properties of metal chart correct?

Can Fine Iron Powder Be Compressed into a Solid Puck Without Heat or Binders?

How can one produce Ferrosilicon

Galvanizing: A Surface Treatment?

Will AZ91E Magnesium Alloy Corrode in Air?

Lennard-Jones potential graph w/ attractive/repulsive force

Transparent Liquid Piezoelectric Material?

ChemE major who hates Organic Chemistry

Are lithium-ion batteries suitable for electric aircraft?

Materials for a Lightweight, Sturdy Mechanical Chair

Finding water-cement ratio for 6525 psi compressive strength

Does nanotube length increase absorption and reflectance?

What causes brittleness in cast iron?

Calculating Moment Capacity of A36 steel plate

What would be a good adhesive material?

Which material is good (cost and strength wise)

Can old neodymium magnets be recycled?

Building a hydrostatic pressure chamber

Is it Safe to Distill Santovac Diffusion Pump Oil in a Common Distiller?

Ball-Park Price Low-temp graphite

Is there a Stuff -> Materials it's made of reference around?

DC Sputtering of Silicon without Magnetron

What is the best approach for layer-by-layer deposition of aluminium oxide?

Gasoline fuel cell (vs. gas generator)

Why do PET bottles have bumps on the bottom instead of being flat?

Why Aren't Desalination Plants Being Utilized for Water Crisis Prevention?

Aluminum square tubing strength

Value of Vout in PMOS Inverter?

Revolutionary Process Reduces Coal Pollution by 99%

Diffnt suppliers, same composition (AlTiB) yielding 2 different Grains

Comparison between aluminium and stainless steel

Difference between Chemical analysis and PMI

Metal plates pressing at 4K, sticking/adhesion problem

How to measure breaking points of different materials?

Are there practical uses for materials with magnetochemical properties?

Using magnetism to control the structure of concrete

Understanding Material Breakage: Fractures, Fatigue, and More

Asme sec viii div 1 interpretation

Advice on approcah for humidity conversions in c#

Pressure drop due to friction and condensation

My Iron from the Earth: A Childhood Memory

Is Carbon More Affinity to Chromium or Nickel in Welding?

Designing a polymer coating process

Safety relief valve discharge piping 4 meters to vent manifold

Rubens Tube - Finding a One Inch Reducer and PTC

Can I use Prony series to fit creep data from relaxation test results?

• Poll

How Does Open Air Influence Chemical Reactions in Furnace Firing?

XRD limitation in detection of a second phase with low amount

Hydrostatic Vacuum Distillation Idea

Equilibrium for diffusion of gases in metals

Initial yield stress Vs. tensile strength

Calculate NaCl density at 20°C in lbm/ft³

How can we combine metal and fiber together?

Internal Energy as a function of U(S,V,A,Ni)

What materials are used in 43mm IR camera lens filters?

How does a photovoltaic cell convert light into electricity?

What Is the Emissivity of Tungsten Carbide?

Could Elements Weigh Differently on Other Planets?

How to determine the dielectric constant of egg tray?

Defenition of prior austenite grain boundary

Silica gel polymerisation modeling

Smart Materials: Liquid to Solid Transformation

Fluid Statics - Forces on Submerged Surface?

I need an area of study to get passionate about

Calculating Water evaporation rate

Burn characteristics of Decro synthetic polypropylene paper

Extracting aluminum from aluminous clays

Tresca and Von mises question

Is permissible stress and tensile strength the same?

Why does a homemade Mylar capacitor produce 5-10 kHz noise with 60 kHz excitation?

What are the physical and chemical properties of API Q125 tubulars?

3D Transport and Adsorption model on Comsol

Choosing materials for a bridge

Can a Neodymium Magnet be used as an electromagnet?

Finding minimum yield strength from Mohr's circle and von Mises stress

Electrolysis Cell Design. (Not for Car)

Polarization Hysteresis Ciruit

Where Can I Find Polymer Blend Sheets for Testing Applications?

Relative humidity calculations.

Momentum balance derivation in equations

Miller indices of Ni based alloys

Why Are Asbestos Sheets Used for Roofing Corrugated?

Rapid chilling water with LN2 pros and cons question

Is there research in a topic such as this?

Making hot air rise faster in flue gas funnel

Heat-treated sample fracturing at tensiometer chuck instead of necking

Strengthening, crystalline alloys, and yield strength questions?

Problem with light manganese phosphate coating (parkerizing)

How to determine steel strength formulas

Allowable load in short compression member

What is the magnetic permeability of clay?

Influence of thermal expansion on thermal conductivity

Current increases rate of corrosion?

Finding strength properties for wooden plank bridges

Calculating Gas Flow Rate and Pressure Drop When Throttling a Cylinder

Manufacturing metal sheets of a car frame

Tempering of martensite with retained austenite

Effect of cross-linking/fillers on relaxation time

Why is Ammonia Stored at -33ºC and P=1bar?

Carbon Steel for High T pipeline