Mechanical Engineering Forum

Gravitational potential energy storage - seeking comments

Basic Engineering design of a small lift

Calculating hydraulic force from cylinder diameter

Bearing press in process problem

Solving a CO2 Air Tank Problem

Gear Ratios and Progressive slowing?

What factors affect the performance of marine propellers?

Bearing steel that can absorb shocks

Steering arm angle for rear steer with Ackermann in FSAE

Modes of vibration, natural frequency

Cost of high capacity compressors ($/kW)

Relationship of Critical Damping Ratio in Elastomers

Can Kinetic Energy Generators Revolutionize Car Efficiency?

Universities with flow control research labs

Is Section Modulus the same as a cross sections bending strength modulus ?

What is the force that causes the misalignment referred to as nutation?

Question involving load on beams

What is 6000 gf.cm (torque) in terms of KG?

Small Rod Wipers? (Or other reliable gasket material?)

[Theory of Machines] Why is Belt in a Belt drive a Link

Is this the new stealth bomber ?

Good idea to do a language module in my MEng degree?

Triggering a camera to detect passing trains

Mechatronics or Computer Systems Engineering for Robotics? Advice Needed!

What is the equation for approximating propeller thrust at a known RPM?

• Poll

Which CFD software is best for a final year project on Heat Exchangers?

Low speed wind tunnel - design and fabrication

Creating a process sheet for satellite part manufacturing

Questions on Bending Stresses (which area will have 0 stress)

What does it take to design a high pressure solar boiler

Specific Standard for Sheetmetal drawings?

Solidworks COSMOS - How to read results

Elastomer Mechanical Properties

Remote Control Car:H-Bridge Vs Simple Switch DPD

How do I calculate the bending energy for a cross-linked beam network?

ASME Useful Resource for Research?

How much force does pressure difference apply to a disk valve?

Can Increasing Pipe Diameter Enhance Home Water Cooling Systems?

Motion of a piston be considered simple harmonic

Flow Distribution for 850m^3/h Fans in Electrical Machines

Is the shaft exerting 600 pounds of force on the table?

When can we use ΔH=CpΔT and ΔU=CvΔT?

Why don't air conditioners have regenerative heat exchangers?

Solar power AC units, soon or never?

How to Calculate Nusselt Number for Air Flow in a Pipe with ANSYS?

Can Sonic Velocity Be Achieved in a Short, Constant Cross-Section Pipe?

What bore diameter will fit a 5.4mm motor shaft?

How do you seal a rotor underwater?

What Are the Best Trigger Mechanisms for Rubber Band Powered Vehicles?

Thermal/HVAC Load Software for Commercial Projects

Equilibrium temperature of heat exchanger

Sealing a rotating rod through a pressurized cylinder

Automated mouse pressing device

How Does a Torque Meter Measure Engine Torque and RPM?

Maximum shear stress in square tubing

Generator Efficiency: Learn About RPM Impact

Is Mechanical Engineering the Right Field for You? Find Out Here!

Need a fastener locking mechanism for #8-32 NC screw.

What Happens If You Block a Fan with a Drag Tube?

Is a Pumpless Cooling System Possible?

Oil temperature in a hydraulic hand pump

Pressure drop across a packed bed

Using PDE Mode in COMSOL to Model Temperature Change

How Much Axle Torque Is Needed to Prevent a Car from Rolling Downhill?

How to learn AutoCAD and 3D design

How does a nuclear submarine reactor cooling loop work?

Accurate Height(above sea level) Measurement Device

Pressure Drop Across Radiator And Air Flow

Alternative Methods to Die Casting :

Force Calculation in deflecting a sheet metal part

Can tire uniformity parameters predict dynamic and static unbalance?

What Can I Expect in an HVAC Industrial Placement?

What factors determine the success of a siphon in draining a water tank?

Efficient Gas Instant Hot Water System with Copper Coil-Cap [Diagram Attached]

Question in U.S. Diesel Emission Standards

How to divide a volume in Gambit for CFD meshing

Calculation of inertia resistance in my geometry

Comsol Multiphysics Heat Transfer

Shear stress on bolts (in different planes)

How Can I Achieve Precise Rapid Rotation in My Mechanical Project?

Thermodynamic efficiency of small diesel engines.

Measuring distance of rotating object

Thermal Conductivity Graph in Comsol

Learning Fluid Power Systems for University Final Year Project

Vibration Damping an Analytical Scale

What Are the Best Hobbies or Entry-Level Jobs for Aspiring Mechanical Engineers?

Build a Pump Using Wind Generator Design

Precombustion chamber and compression chamber

Heat transfer into constant temp sink

How can a student create a gas turbine engine from scratch?

Solving Beam Deflection Problem with Variable Moment of Inertia

Is 4Frontiers Paving the Way for Permanent Mars Colonization?

Electromagnet with 200+ wire turns won't attract paper clips

What subjects and skills should I learn to prepare for mechanical engineering?

Need a formula to calculate BTU loss in a pond.

HP Air Bottle Sizing for 4.19m³ Tank at 10 Bar

Air driven turbine for generator and flywheel?

How Can I Determine the RPM of My Pond Pump?

How long should a BBQ grill utensil handle be to stay cool?

To heat treat or not to heat treat